Heet-O-Matic	MODEL 290	MODEL 492	MODEL 309 55 Gallon Drum Heater
MODEL 560	MODEL 540	L-Shaped Tank Heater	Vertical Mount Titanium Heater

Match-Mated Immersion Heater with Thermostat

Here's the ideal immersion heater for rapid heating plus precise liquid temperature control all in one combined unit!

Immersion Heaters

Pilot light indicator makes temperature setting easy!

Match-Mated Immersion Heater with Thermostat
Model 306

The Ulanet Heet-O-matic Model 306 immersion heater was designed to provide an easy to use trouble-free source of controlled heat for quick sterilization in laboratories, as well as a controlled heat source for general laboratory liquid heating. This immersion heater is supplied with a standard 6" B length. For X-ray film developing the Model 306 is supplied with a 20" B length. The design of the Model 306 allows quick and convenient over the side mounting for heating liquids in open tanks.

The Model 305 Heet-O-matic immersion heater with its 1" standard N.P.T. is for permanent through-the-side tank installation in such applications as knife sterilizers, carpet cleaning equipment, automatic grease interceptors, distillers, photographic developing.

Model 335 Immersion Heater

ADJUSTMENT:

Adjustment knob is set with the "off" position at room temperature. To increase temperature setting, adjustment knob is turned clockwise.

Model 324 Immersion Heater

FEATURES:

Thermostat probe and heater element sheath and dome switch cover are made of polished Type 316 stainless steel.
Heating element configuration protects sensitive thermal probe against mechanical damage.
Pilot light indicator shows "ON" when unit is heating.
Supplied with a 6' 3-wire cordset.
Rating 500W. or 1100W. or 1500W. at 115 or 230 V.A.C.
Differential: ± 1°F in a circulated bath.
Model 305 500W. or 1100W. has a 5-1/2" length, while the 1500W. has a 7" length.

Model 305MP

CAUTION:

1" from the top of models 305 and 306,
2" from the top of model 335 and
4" from the top of model 324.

Back to the top

Models 290, 297 and 492 Immersion Heaters

MODEL 492-1

MODEL 492-2

MODEL 492-3

MODEL 492-4
MODEL 492-6

MODEL 297-2
MODEL 301-2

EQUIPPED WITH PILOT LIGHT, 6' 3-WIRE GROUNDED CORDSET, AND THERMOSTAT CONTROL ADJUSTABLE EITHER 70°-250°F, OR 120°-570°F.

Design permits hanging over edge of vessel. Heating elements are contained in coil section to concentrate heat at the bottom of the vessel. Risers are unheated. Units are ideal for heating suitable liquids in laboratory and industrial use. Requires a liquid level of 5" minimum above the bottom heating coil.

Heating element sheath is polished Type 316 stainless steel.

Utility, Beaker and Pan Immersion Heaters

Back to the top

MODEL 290-2

MODEL 290-4

MODEL 290-6

EQUIPPED WITH ULANET ROBOTEMP STEPLESS HEAT CONTROL, PILOT LIGHT AND 3-WIRE, 6' GROUNDED CORDSET.

Design permits hanging over edge of vessel. Heating elements are contained in coil section to concentrate heat at the bottom of the vessel. Risers are unheated. Units are ideal for heating liquids of all types in laboratory and industrial use. Requires a liquid level of 5" minimum above the bottom heating coil.

Heating element sheath is polished Type 316 stainless steel.

Back to the top

SCREW PLUG IMMERSION HEATER: 1", 2", 2 1/2" NPT Standard

Single or three phase voltages up to 480 - 3 phase.
Available with 3 phase thermostats for ratings up to 10kW.
Optional general purpose or explosion-proof terminal housing

Screw Plug Immersion Heaters
Mounted with compression fittings

Back to the top

MODEL 309 55 GALLON DRUM HEATER

Standard Dimensions: 19" Diameter, 36" Height
SHEATH: T-316 Stainless Steel
STANDARD RATING: 5000 WATTS 230V
Supplied with thermostat adjustable 70°-250°F and pilot light
Requires a liquid level of 10" minimum above the bottom heating coil.

Back to the top

MODEL 560

Waterproof Stainless Steel Enclosure

T-316 Stainless Steel Sheath

1" NPT fitting with 5-1/2" Standard Length

1100W 115V Standard Rating

Supplied with a standard series thermostat at 190°F and a 6' 3-wire cordset

Available with ratings of 500W or 1500W 115V and other thermostat settings

Back to the top

MODEL 540-2

MODEL 540-4

MODEL 540-6

Waterproof PVC enclosure
Equipped with a 6' 3-wire cordset
Thermostat control adjustable 70°- 250°F

Back to the top

L-SHAPED TANK HEATER

Available with T-316 stainless steel or Incoloy 800 sheath.

Can be supplied with a 3 phase thermostat, adjustable 70°- 250°F
with a safety cut-out for ratings up to 10kW

Back to the top

VERTICAL MOUNT TITANIUM HEATER

For plating or chemical etching. Supplied with PVC cap, mounting plate & cord.

Back to the top

Accurate Imaging, Inc. 1999